Here is the pinout shown from the end of the plug. The ID pin is used by the USB controller to determine the intented role that the controller has to switch to depending on the end of the cable that gets plugged into the USB connector.
Universal Serial Bus On- The- Go aka USB OTG is the feature that adds USB device compatibility to mobile devices. Writing to this register triggers a host transaction. TI USB-OTG Enabled Solutions • Many DSP/OMAP™/IAG devices have integrated USB OTG digital cores – Some are USB 2.0 full-speed only (12 Mbps), while some support USB 2.0 high-speed (480 Mbps).

Don't have an OTG adapter for your new Raspberry Pi Zero? Obviously, this forms part of some overcurrent protection circuit, but I have no idea what I'm supposed to do with it. USB On-The-Go (OTG) USB On-The-Go (OTG) 27 • U1TOK Register The U1TOK is a read/write register required when the module operates as a host. August 22, 2013, 12:00 am PDT. Table 1 shows the pin-out for both receptacle and plug. In order for your Android phone or tablet to host a USB device such as an Arduino, you need an On-The-Go (OTG) USB cable. 3: This bit field is contained in the OSCCON register. The one thing I am confused about at the moment is the purpose and function of the "ID" pin included in the header. The 124 kΩ mode is slightly more complicated to wire: place a 124 kΩ resistor between ID and GND. Firmware reads CIDSTS bit in OTG_FS_GOTGCTL, to see the level of ID pin (0 = plug in of 'A' plug) > and a‘B’USB cable (connected to PC for VCP serial port ).

USB 2.0 is the successor standard was released in 2000 with the new transfer mode Hi-speed that can transfer data at up to 480 Mbit/s (40x times higher the rate of USB 1.0). USB On-The-Go (OTG) USB On-The-Go (OTG) 27 Figure 27-1: PIC32 USB OTG Interface Diagram Note 1: PB clock is only available on this pin for select EC modes. There is one more ID pin (pin 4) on micro USB which you have to connect it to Ground (pin 5) so that the host device (phone) knows when there is an USB On-The-Go (OTG) device connect to it. charge its battery) as well as act as a USB host.

The fact that you are trying to test OTG the ID pin should be directly connected to the USB controller ID pin on the DaVinci device. Like • Show 0 Likes 0; Comment • 18; hi, I need to detect the usb based on usb otg id pin on imx6q saberauto platfrom. USB cable, female type A. USB cable, male micro B. usb detection based on usb otg id pin. • TI is working on discrete transceivers Section 27. ID pin configured below,

2: Pins can be used as digital inputs when USB is not enabled. USB Micro-B Connector. It is used to specify the token type, PID<3:0>, and the endpoint, EP<3:0>, being addressed by the host processor. Requesting clarification regarding USBID pin behavior Hi! The term was first used in 2001 but took a few more years to be fully real. The STOTG04 transceiver is suitable for mobile and battery Don't Worry! If VDD is 3.3 V pull-up may be connected directly to USB_DMPU pin. This video shows you how to solder a usb extension cable into the raspberry pi zero, giving you a full size usb … It provides complete physical layer (PHY) solution for any USB-OTG device. Raspberry Pi Zero OTG Mode.

The ID pin can also have a 124 kΩ impedence to ground (see below). Homepage Unlike past fingerprinting proposals we wirelessdevice. The STOTG04 is a USB On-The-Go full-speed transceiver.

AN_11201 USB OTG-like Connector Implementation This application note helps developers implement a USB OTG-like connector on Atmel SAM9 5-series and SAMA5D3x devices.